- CARS
- IF11 - 1/10 FORMULA
- IF11-2 1/10 FORMULA
- IF14 - 1/10 EP TC
- IF14-2 - 1/10 EP TC
- IF14-2 FWD - 1/10 EP TC
- IF14-2 FWD RS - 1/10 EP TC
- IF14-2 TEAM EDITION
- IF14-2 MID
- IF15 - 1/10 GP TC
- IF15W - 1/10 GP TC WIDE
- IF15-2 - 1/10 GP TC
- IF15-2W
- IF18 - 1/8 GP ONROAD
- IF18-2 - 1/8 GP ONROAD
- IF18-3 - 1/8 GP ONROAD
- IFB8 - 1/8 NITRO BUGGY
- IF11 - 1/10 FORMULA
- SPARE PARTS
- IF11 SPARES
- IF11-2 SPARES
- IF14 SPARES
- IF14-2 SPARES
- IF14-2 FWD SPARES
- IF14-2 FWD RS SPARES
- IF14-2 TE SPARES
- IF14-2 MID SPARES
- IF15 SPARES
- IF15W SPARES
- IF15-2 SPARES
- IF15-2W SPARES
- IF18 SPARES
- IF18-2 SPARES
- IF18-3 SPARES
- IFB8 - SPARES
- IF11 SPARES
- OPTION PARTS
- IF11 OPTIONALS
- IF11-2 OPTIONALS
- IF14 OPTIONALS
- IF14-2 OPTIONALS
- IF14-2 FWD OPTIONALS
- IF14-2 FWD RS OPTIONALS
- IF14-2 TE OPTIONALS
- IF14-2 MID OPTIONALS
- IF15 OPTIONALS
- IF15W OPTIONALS
- IF15-2 OPTIONALS
- IF15-2W OPTIONALS
- IF18 OPTIONALS
- IF18-2 OPTIONALS
- IF18-3 OPTIONALS
- IFB8 - OPTIONALS
- IF11 OPTIONALS
- Accessories
- Infinity 1/8 onroad
16 other products in the same category:
R0326 - TEAM SPEC BEARING(8x14x4) 2pcs
These bearings are the same high-spec bearings used by INFINITY team drivers during big races such as World Championships. These precision bearings are not only super smooth but also extremely durable.
R0331 - Fuel Tank Spacer Set(IF18-2)
A spacer/insert set that matches the fuel tank capacity of IF18-2 with the regulations of international races such as IFMAR. The thinnest spacer is 0.5cc, allowing you to make fine adjustments to the tank capacity by increasing or decreasing the number spacers.
CM-A005-30: ALUMINUM WASHER 3x6x3.0mm (Red/10pcs)
A vivid red anodized version has been added to the aluminum spacer series (3mm in inner diameter). It helps you dress up your machine. If you use this red anodized version and the black version in different specifications in a setting, you can easily distinguish them.
R0327 - ALUMINIUM OFFSET BUSHING (IF18-2)
Machined from high quality A7075 aluminium material. IF18-2 knuckle upper and lower insert. Prevents misalignment during a crash and enhances steering response during cornering. This bushing is used for -1mm/+1mm (trail/reverse trail) of the upper pivot.
When assembling these parts first remove the front knuckle upper. Place the offset bush into the knuckle upper from the outside. Then pass both M3x14mm slim head screws through the knuckle upper from the inside and tighten the 3mm nylon nut on the outside.
R0256 - BUMPER SPACER SET
NEW Option part for IF18.
Insert under front bumper to adjust body height where needed.
Ideal when running on bumpy race tracks.
Will offer a smoother driving feel.
Includes M4mm Aluminium Nylon Nut & M4x12mm Titanium Flat Head Screw.