![](http://www.creationmodel.net/catalog/278-large_default/r0204-bearing-sp-5x8x25-2pcs.jpg)
![](http://www.creationmodel.net/catalog/278-home_default/r0204-bearing-sp-5x8x25-2pcs.jpg)
![](http://www.creationmodel.net/catalog/276-home_default/r0204-bearing-sp-5x8x25-2pcs.jpg)
![](http://www.creationmodel.net/catalog/277-home_default/r0204-bearing-sp-5x8x25-2pcs.jpg)
The most advanced "PRS system" will deliver faster cornering speed for IF14.
As a function of stroke from suspension arm, toe angle is controled passively.
Amount of toe angle is fine-tuned by mounting angle of linkage rod.
Height of steering block is alternative of two types and roll-center can be adjusted .
The system is capable of various track condition or layout of the corner.
Including 40mm size high speed cooling fan is mounted at back side of motor. Fan is fixed with two screws on the red anodized aluminum fan mount. Since this fan mount is fixed on chassis by one screw so as hardly can not effect chassis flex. Mount is usable for 30mm and 40mm size fan.
※ Not combination usage with T095 Rear balance weight (Left side).
※ Limited-production item.
Reviewed steering angle, front D.J.CVD drive shaft.
With use of aluminum bell crank (T093), smoothly can provide the drive power at wide steering angle.
Assemblage of wheel axle and drive shaft must be Ver.2 -to-Ver.2
Aluminum spool outdrive with shining antiwear hard anodized coating. Made by 7075 T6 material.
Comparing normal type per car, approx. 6.8g light weight. Better throttle response achieved.
Use with C-Blade protector (T124) for drive shaft.
Material is softer than kit normal. Higher drive efficiency achieved by narrowed belt. Exclusive use for stock motor.
Newly designed rear upright, geometry of suspension system is optimized. Toe angle is zero.
Mounting position of upper arm is optimized at higher point, shim of 2.0mm to be reduced.
Lineup of Hard & Graphite material. Hard material suits for fundamental condition and provides stable grip.
For high grip surface and expecting quick response, graphite material is recommended to use.
The new suspension holder provides 0.5mm lower than kit normal hinge pin point. Possible to lower the roll center. Combination of roll center and toe angle option, setting range is widen.
Newly designed rear upright, geometry of suspension system is optimized. Toe angle is zero.
Mounting position of upper arm is optimized at higher point, shim of 2.0mm to be reduced.
Lineup of Hard & Graphite material. Hard material suits for fundamental condition and provides stable grip.
For high grip surface and expecting quick response, graphite material is recommended to use.
Newly designed steering block. Steering angle stopper is additionally equipped.
Steering is adjustable at any angle of incidence. Lineup of Hard & Graphite material.
Hard material is suitable for fundamental condition and provides stable grip.
For high grip surface and expecting quick response, graphite material is recommended to use.
Newly designed steering block. Steering angle stopper is additionally equipped.
Steering is adjustable at any angle of incidence. Lineup of Hard & Graphite material.
Hard material is suitable for fundamental condition and provides stable grip.
For high grip surface and expecting quick response, graphite material is recommended to use.
The newly designed gear differential for IF14 offers smooth rotation and high rear traction in all conditions. The differential shafts are now supported by ball bearings for added stability and consistency during runs. Outdrive cups can now be replaced from the outside without the need to open the diff making maintenance quick and easy.
This is a set of 4.9mm ball ends made of strong and high-precision hard steel. The screw part is shorter than the 5mm ones. The ball surface is smoother than that of the conventional one (T049), yet sold at a competitive price.
By adding these wheel shims between the hex wheel hub and the wheel, you can fine-tune the cars track width quickly. Available in two thicknesses of 0.25mm and 0.5mm. 8pcs are included in each.
The most advanced "PRS system" will deliver faster cornering speed for IF14.
As a function of stroke from suspension arm, toe angle is controled passively.
Amount of toe angle is fine-tuned by mounting angle of linkage rod.
Height of steering block is alternative of two types and roll-center can be adjusted .
The system is capable of various track condition or layout of the corner.