Wheel shaft for IF15-2 with a hybrid structure of hard-anodized A7075 for the main body and titanium for the axle shaft threads, achieving a high level of strength and weight reduction.
Weight reduction of 1.9g compared to the normal steel (4.5g); about 10g reduction in rotating mass for one unit.
Adjustment tool that fits directly onto clutch nuts such as IF18-3 and IF15-2. The flat top surface makes it easy to apply force when tightening the nut and enables easy installation even with hard clutch springs.
Reviewed steering angle, front D.J.CVD drive shaft.
With use of aluminum bell crank (T093), smoothly can provide the drive power at wide steering angle.
Assemblage of wheel axle and drive shaft must be Ver.2 -to-Ver.2
A new #900 has been added to the INFINITY silicon shock oil series.
This allows for a wider range of settings in all categories.
Not only has rigidity been increased by using A7075, but the pivot height has been raised by 2mm compared to the standard part R300B/300H, providing more responsive steering and changing the camber change rate. To ensure clearance inside the wheel, the ball has been downsized from 8.5 to 8.0mm and the screw cap from 10 to 9mm and tilted by 10°. A specially prepared 8mm titanium ball is included to ensure proper steering angle. The main body is hard anodized.
Mounted in the opening at the rear of the main chassis, it increases chassis rigidity at the rear end of the chassis and increases weight by approximately 13g to ensure stable rear grip. It is also effective when the track surface is high grip and traction roll occurs.
Use with G230 Carbon Rear Stiffener Set to expand the range of setting.
Pinion gear with improved durability compared to the standard part, achieved by reviewing the material and coating.
New stabilizer stopper for IF18-3 front stabilizer.
By making the contact surface with the bearing spherical, smoother movement of the stabilizer is acheived.
Durability has also been greatly improved by using steel.
Available in 2.3, 2.5, and 2.7mm.
Compatible stabilizers
Stopper 2.3mm (R0382S23): 2.0mm, 2.1mm, 2.2mm, 2.3mm
Stopper 2.5mm (R0382S25): 2.4mm, 2.5mm
Stopper 2.7mm (R0382S27): 2.6mm, 2.7mm
The belt roller set will prevent skipping of rear belt of IF14.
When it occurs deflection under huge load on the belt, helps the belt to keep at proper position.
It provides stability of traction and brake control. It lengthens the life of belt.
※No combined usage with T095 REAR BALANCE WEIGHT.
Prevents the side belt from falling off when a heavy load is applied to it.
Newly designed rear upright, geometry of suspension system is optimized. Toe angle is zero.
Mounting position of upper arm is optimized at higher point, shim of 2.0mm to be reduced.
Lineup of Hard & Graphite material. Hard material suits for fundamental condition and provides stable grip.
For high grip surface and expecting quick response, graphite material is recommended to use.
The combination of carbon and aluminum materials provides sharp steering characteristics with a highly rigid and lightweight finish. In addition, the included 4.9mm ball and aluminum spacer optimize bump steer and increase corner speed.
The new suspension holder provides 0.5mm lower than kit normal hinge pin point. Possible to lower the roll center. Combination of roll center and toe angle option, setting range is widen.
The new suspension holder provides 0.5mm lower than kit normal hinge pin point. Possible to lower the roll center. Combination of roll center and toe angle option, setting range is widen.
The most advanced ""PRS system"" will deliver faster cornering speed for IF14. As a result of the stroke from suspension arm, toe angle is controled passively. Amount of toe angle is fine-tuned by the mounting angle of the linkage rod.
Rear caster angle is -2 deg.
1/10 GP Touring Car World Championship
At the 2018 IFMAR 1/10 GP Touring Car World Championship (1/10 IC Track), five cars made it to the A main final, qualifying TQ and winning the championship. Four years after that amazing debut, at the 2022 IFMAR World Championship, nine IF15 prototypes made it to the A main final, qualifying TQ, Superpole, and winning, proving their overwhelming potential. The IF15 prototypes that achieved these amazing results are finally being made commercially available as the IF15-2!
The IF15-2, the most advanced 1/10 GP touring car in history and will take your racing to new heights!
Let's aim for the top together!
Wheel shaft for IF15-2 with a hybrid structure of hard-anodized A7075 for the main body and titanium for the axle shaft threads, achieving a high level of strength and weight reduction.
Weight reduction of 1.9g compared to the normal steel (4.5g); about 10g reduction in rotating mass for one unit.
