R0382S25 - SWAY BAR STOPPER 2.7mm (IF18-3/2pcs)

Reviewed steering angle, front D.J.CVD drive shaft.
With use of aluminum bell crank (T093), smoothly can provide the drive power at wide steering angle.
Assemblage of wheel axle and drive shaft must be Ver.2 -to-Ver.2

Spare part for G260

This component is crafted from 7075-T6 alloy and features a hard coating. Its lightweight design (4.3 grams compared to the steel version's 8.3 grams) allows you to save weight and achieve maximum performance. It can also be installed on the rear hub. Using the M170 on the rear end of your vehicle provides additional support, which is recommended for high-grip and fast tracks.

The combination of carbon and aluminum materials provides sharp steering characteristics with a highly rigid and lightweight finish. In addition, the included 4.9mm ball and aluminum spacer optimize bump steer and increase corner speed.

New axle shaft is high-duty concrete steel material used. Grind extremely to the limit and achieved light weight.
Fit together perfectly with the drive shaft material 7075 T6 made in Japan.
Black anodized drive shaft is light weight and "INFINITY" logo is marked.
M3 set screw is used at universal spider for simple operation.
Each parts are finished as possible as smooth that is with zero waste for further cornering speed and throttle response.

This part is crafted from 7075-T6 alloy, significantly enhancing the stiffness of the central diff mounting. Additionally, it improves heat dissipation and facilitates a smoother transmission, resulting in enhanced performance.

Newly designed rear upright, geometry of suspension system is optimized. Toe angle is zero.
Mounting position of upper arm is optimized at higher point, shim of 2.0mm to be reduced.
Lineup of Hard & Graphite material. Hard material suits for fundamental condition and provides stable grip.
For high grip surface and expecting quick response, graphite material is recommended to use.

Reviewed steering angle, front D.J.CVD drive shaft.
With use of aluminum bell crank (T093), smoothly can provide the drive power at wide steering angle.
Assemblage of wheel axle and drive shaft must be Ver.2 -to-Ver.2

The most advanced ""PRS system"" will deliver faster cornering speed for IF14. As a result of the stroke from suspension arm, toe angle is controled passively. Amount of toe angle is fine-tuned by the mounting angle of the linkage rod.
Rear caster angle is -2 deg.

The shock tower Ver.B is made up after continuous feedback from Team INFINITY drivers in the worlds
Newly designed shock positions will provide you stable grip balance in various condition.
Perfectly suitable when you like to make the driving feel milder than kit normal.

Not only has rigidity been increased by using A7075, but the pivot height has been raised by 2mm compared to the standard part R300B/300H, providing more responsive steering and changing the camber change rate. To ensure clearance inside the wheel, the ball has been downsized from 8.5 to 8.0mm and the screw cap from 10 to 9mm and tilted by 10°. A specially prepared 8mm titanium ball is included to ensure proper steering angle. The main body is hard anodized.

A new #900 has been added to the INFINITY silicon shock oil series.
This allows for a wider range of settings in all categories.

R0342 is made with carbon mixed material to greatly increase the rigidity of the parts. The rear upper arm and wheel shaft support are more rigid, and rear traction is improved at all speeds.

This component is crafted from 7075-T6 alloy and features a hard coating. Its lightweight design (0.65 grams) allows you to cut weight from your transmission and achieve maximum performance. It can be installed on all the differentials of your vehicle.

In addition to the conventional 9, 10, and 11mm, the new 8mm is now available as a set with the necessary parts for installation!
 By using 8mm, the outer wheel has more angle allowing for a wider range of settings.
 R0259 Aluminum Servo Saver Set (top mount) is required.

A special manufacturing process ensures long life and consistent performance.
As the overall length is approximately 11mm,
please use it together with R0413 CLUTCH SPRING HOLDER (for R0412).