Brake pads that can be used with IF15-2/2W and IF18-3.
Compared to the standard soft (red), this pad enhances initial braking, allowing you to tune your preferred feeling when entering the corner.
By mixing this pad with the standard (soft (red)), you can create an intermediate feeling.
(There is an identification marking on one side, apply adhesive to this side only)
M3x5mm and M3x12mm have been added to the popular INFINITY titanium slim head screw lineup.
They can now be used in more locations.
M3x5mm and M3x12mm have been added to the popular INFINITY titanium slim head screw lineup.
They can now be used in more locations.
Newly designed rear upright, geometry of suspension system is optimized. Toe angle is zero.
Mounting position of upper arm is optimized at higher point, shim of 2.0mm to be reduced.
Lineup of Hard & Graphite material. Hard material suits for fundamental condition and provides stable grip.
For high grip surface and expecting quick response, graphite material is recommended to use.
This component is crafted from 7075-T6 alloy and features a hard coating. Its lightweight design (0.65 grams) allows you to cut weight from your transmission and achieve maximum performance. It can be installed on all the differentials of your vehicle.
Reviewed steering angle, front D.J.CVD drive shaft.
With use of aluminum bell crank (T093), smoothly can provide the drive power at wide steering angle.
Assemblage of wheel axle and drive shaft must be Ver.2 -to-Ver.2
The new suspension holder provides 0.5mm lower than kit normal hinge pin point. Possible to lower the roll center. Combination of roll center and toe angle option, setting range is widen.
Reviewed steering angle, front D.J.CVD drive shaft.
With use of aluminum bell crank (T093), smoothly can provide the drive power at wide steering angle.
Assemblage of wheel axle and drive shaft must be Ver.2 -to-Ver.2
Steering knuckle plate for IF15-2 and IF15-2W, which allows for a greater steering angle of the outer tire in corners than the standard kit version.
This will make tighter cornering possible, and can improve high speed steering on larger tracks.
The most advanced ""PRS system"" will deliver faster cornering speed for IF14. As a result of the stroke from suspension arm, toe angle is controled passively. Amount of toe angle is fine-tuned by the mounting angle of the linkage rod.
Rear caster angle is -2 deg.
Pinion gear with improved durability compared to the standard part, achieved by reviewing the material and coating.
Made of superior quality 1.6mm thickness of U.S.A. carbon material.
Compare with kit normal thickness 2.0mm, further chassis flex is gained and initial steering response can be increased.
Provides great efficiency use with optional Aluminum Flex Main Chassis(T109).
Mounted in the opening at the rear of the main chassis, it increases chassis rigidity at the rear end of the chassis and increases weight by approximately 13g to ensure stable rear grip. It is also effective when the track surface is high grip and traction roll occurs.
Use with G230 Carbon Rear Stiffener Set to expand the range of setting.
New stabilizer stopper for IF18-3 front stabilizer.
By making the contact surface with the bearing spherical, smoother movement of the stabilizer is acheived.
Durability has also been greatly improved by using steel.
Available in 2.3, 2.5, and 2.7mm.
Compatible stabilizers
Stopper 2.3mm (R0382S23): 2.0mm, 2.1mm, 2.2mm, 2.3mm
Stopper 2.5mm (R0382S25): 2.4mm, 2.5mm
Stopper 2.7mm (R0382S27): 2.6mm, 2.7mm
Brake pads that can be used with IF15-2/2W and IF18-3.
Compared to the standard soft (red), this pad enhances initial braking, allowing you to tune your preferred feeling when entering the corner.
By mixing this pad with the standard (soft (red)), you can create an intermediate feeling.
(There is an identification marking on one side, apply adhesive to this side only)
